| Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision |
| slackware:setup [2007/10/08 19:29] – The command "mount -o bind /dev /mnt/dev" sometimes fails alien | slackware:setup [2008/02/14 17:49] – Changes in LILO explanation alien |
|---|
| |
| FIXME | FIXME |
| | |
| |
| ===== Encrypted partitions ===== | ===== Encrypted partitions ===== |
| |
| FIXME | FIXME |
| | |
| | Installation to encrypted partitions works well with the stock Slackware kernels.\\ |
| | If you want to compile your own custom kernel to work with LUKS encrypted partitions you need to enable at least the following two options in your kernel configuration: <code> |
| | Multiple devices driver support (RAID and LVM) ---> |
| | <*> Device mapper support |
| | <*> Crypt target support |
| | </code> This is equivalent to the following options in your ''.config'' file: <code> |
| | CONFIG_BLK_DEV_DM=y |
| | CONFIG_DM_CRYPT=y |
| | </code> Do not compile these as module! They are required in your kernel. |
| | |
| | ===== Using an initrd with a big kernel ===== |
| | |
| | When you use an initrd file for your box(a requirement for installing Slackware to LVM or LUKS partitions) you will notice that there is a maximum to the size of the kernel you use with it. |
| | If the kernel grows to big (like with the //'huge'// kernels of Slackware > 12.0) you will see the following //lilo// error message: <code> |
| | Warning: The initial RAM disk is too big to fit between the kernel and the 15M-16M memory hole. |
| | It will be loaded in the highest memory as though the configuration file specified "large-memory" |
| | and it will be assumed that the BIOS supports memory moves above 16M. |
| | </code> As far as I know there is no remedy against this message - you need to shrink your kernel until there is room for the initrd image. A Slackware //'generic'// kernel is small enough. The recommendation for //'huge'// kernels is that they are not meant for daily use anyway. Either you compile your own custom kernel, or use one of the generic kernels with an initrd. |
| |
| |
| </code> which will add the required files intto the installed system so that lilo will install successfully. I have had reports from several people who experienced the above error, and I have seen it happen myself too, for reasons unclear to me. | </code> which will add the required files intto the installed system so that lilo will install successfully. I have had reports from several people who experienced the above error, and I have seen it happen myself too, for reasons unclear to me. |
| |
| * Second:\\ When the README mentions __''Change the boot device to name of the small unencrypted partition you've created and which is mounted under /boot'.'__ it must be clear that this action should __not__ be taken when you install LILO to the MBR. The example in the README is meant for a Slackware setup where there is another OS bootloader (such as MS Windows) already installed in the MBR, and your Slackware installation is a secondary install for which LILO needs to install itself into the root sector of a partition instead. | * Second:\\ The README_CRYPT.TXT mentions __''Change the boot device to name of the small unencrypted partition you've created and which is mounted under /boot''__ - it should be clear that this advice should __not__ be taken when you configured LILO to be installed in the MBR.\\ The example shown in README_CRYPT.TXT is for a Slackware setup when there is another OS bootloader (such as MS Windows) already installed in the MBR, and your encrypted Slackware installation is a secondary install for which LILO needs to be installed into the root sector of a partition instead.\\ If you are installing Slackware as the first and only Operating System on the computer, please configure ''/etc/lilo.conf'' so that LILO installs into the MBR. You still need that small unencrypted partition for ''/boot'' of course... LILO can only load the kernel and initrd if they are found on an unencrypted medium. |
| | |
| | * Third:\\ When you run the ''lilo'' command and you are using LVM and/or LUKS-encrypted partitions, lilo will show the following warning message (or something very similar): <code> |
| | Warning: "/proc/partitions' does not match '/dev' directory structure. |
| | Name change: '/dev/dm-0' -> '/dev/mapper/cryptroot' |
| | Warning: Name change: ... etc. |
| | </code> These messages are harmless and you can safely ignore them. |
| |
| I hope this clarifies the issues some people reported to me after Slackware 12.0 was released. | I hope this clarifies the issues some people reported to me after Slackware 12.0 was released. |
| |
| -- Eric //03-july-2007// | -- Eric //03-july-2007// |
