Next revision | Previous revisionLast revisionBoth sides next revision |
slackware:setup [2007/06/14 21:16] – created. alien | slackware:setup [2008/02/14 17:49] – Changes in LILO explanation alien |
---|
| |
===== Install to Logical Volumes (LVM) ===== | ===== Install to Logical Volumes (LVM) ===== |
| |
| FIXME |
| |
| |
===== Encrypted partitions ===== | ===== Encrypted partitions ===== |
| |
| FIXME |
| |
| Installation to encrypted partitions works well with the stock Slackware kernels.\\ |
| If you want to compile your own custom kernel to work with LUKS encrypted partitions you need to enable at least the following two options in your kernel configuration: <code> |
| Multiple devices driver support (RAID and LVM) ---> |
| <*> Device mapper support |
| <*> Crypt target support |
| </code> This is equivalent to the following options in your ''.config'' file: <code> |
| CONFIG_BLK_DEV_DM=y |
| CONFIG_DM_CRYPT=y |
| </code> Do not compile these as module! They are required in your kernel. |
| |
| ===== Using an initrd with a big kernel ===== |
| |
| When you use an initrd file for your box(a requirement for installing Slackware to LVM or LUKS partitions) you will notice that there is a maximum to the size of the kernel you use with it. |
| If the kernel grows to big (like with the //'huge'// kernels of Slackware > 12.0) you will see the following //lilo// error message: <code> |
| Warning: The initial RAM disk is too big to fit between the kernel and the 15M-16M memory hole. |
| It will be loaded in the highest memory as though the configuration file specified "large-memory" |
| and it will be assumed that the BIOS supports memory moves above 16M. |
| </code> As far as I know there is no remedy against this message - you need to shrink your kernel until there is room for the initrd image. A Slackware //'generic'// kernel is small enough. The recommendation for //'huge'// kernels is that they are not meant for daily use anyway. Either you compile your own custom kernel, or use one of the generic kernels with an initrd. |
| |
| |
| ===== Errata ===== |
| |
| **__README_CRYPT.TXT__** |
| |
| I'd like to correct two things omitted in the [[http://slackware.osuosl.org/slackware-12.0/README_CRYPT.TXT|README_CRYPT.TXT]] file for Slackware 12.0. They relate to setting up an //encrypted root// partition in Slackware.\\ |
| |
| * First issue: \\ When you finish the installation and the README prompts you to __''perform a chroot into the new |
| installation''__, there is one command missing. As a result, there will not be a ''/dev/mapper/cryptroot'' available inside the //chroot// and therefore the attempt to install LILO will fail.\\ Please change the list of commands that goes like <code> |
| mount -o bind /proc /mnt/proc |
| mount -o bind /sys /mnt/sys |
| chroot /mnt |
| </code> to <code> |
| mount -o bind /proc /mnt/proc |
| mount -o bind /sys /mnt/sys |
| mount -o bind /dev /mnt/dev |
| chroot /mnt |
| </code> and then proceed with the remainder of the README.\\ __IF__ for whatever reason you get something like this error after running "''mount -o bind /dev/mnt/dev''": <code> |
| mount: wrong fs type, bad option, bad superblock on /dev, missing codepage or other error |
| In some cases useful info is found in syslog - try dmesg | tail |
| </code> then please run this command instead: <code> |
| cp -a /dev/mapper /mnt/dev/ |
| </code> which will add the required files intto the installed system so that lilo will install successfully. I have had reports from several people who experienced the above error, and I have seen it happen myself too, for reasons unclear to me. |
| |
| * Second:\\ The README_CRYPT.TXT mentions __''Change the boot device to name of the small unencrypted partition you've created and which is mounted under /boot''__ - it should be clear that this advice should __not__ be taken when you configured LILO to be installed in the MBR.\\ The example shown in README_CRYPT.TXT is for a Slackware setup when there is another OS bootloader (such as MS Windows) already installed in the MBR, and your encrypted Slackware installation is a secondary install for which LILO needs to be installed into the root sector of a partition instead.\\ If you are installing Slackware as the first and only Operating System on the computer, please configure ''/etc/lilo.conf'' so that LILO installs into the MBR. You still need that small unencrypted partition for ''/boot'' of course... LILO can only load the kernel and initrd if they are found on an unencrypted medium. |
| |
| * Third:\\ When you run the ''lilo'' command and you are using LVM and/or LUKS-encrypted partitions, lilo will show the following warning message (or something very similar): <code> |
| Warning: "/proc/partitions' does not match '/dev' directory structure. |
| Name change: '/dev/dm-0' -> '/dev/mapper/cryptroot' |
| Warning: Name change: ... etc. |
| </code> These messages are harmless and you can safely ignore them. |
| |
| I hope this clarifies the issues some people reported to me after Slackware 12.0 was released. |
| |
| -- Eric //03-july-2007// |